JTAG and OnCE Interface
2.12 JTAG and OnCE Interface
The DSP56300 family and in particular the DSP56311 support circuit-board test strategies that
are based on the IEEE 1149.1 Standard Test Access Port and Boundary Scan Architecture , the
industry standard developed under the sponsorship of the Test Technology Committee of IEEE
and the JTAG.
The OnCE module provides a means to interface nonintrusively with the DSP56300 core and its
peripherals so that you can examine registers, memory, or on-chip peripherals. Functions of the
OnCE module are provided through the JTAG TAP signals.
For programming models, see the chapter on debugging support in the DSP56300 Family
Manual .
Table 2-15. OnCE/JTAG Interface
Signal
Name
TCK
TDI
Type
Input
Input
State
During
Reset
Input
Input
Signal Description
Test Clock —A test clock input signal to synchronize the JTAG test logic.
Test Data Input —A test data serial input signal used for test instructions and
data. TDI is sampled on the rising edge of TCK and has an internal pull-up
resistor.
TDO
Output
Tri-stated
Test Data Output —A test data serial output signal for test instructions and
data. TDO is tri-statable and is actively driven in the shift-IR and shift-DR
controller states. TDO changes on the falling edge of TCK.
TMS
Input
Input
Test Mode Select —Sequences the test controller’s state machine. TMS is
sampled on the rising edge of TCK and has an internal pull-up resistor.
TRST
Input
Input
Test Reset —Initializes the test controller asynchronously. TRST has an
internal pull-up resistor. TRST must be asserted after power up.
DE
Input/
Output
Input
Debug Event —As an input, provides a means of entering debug mode from an
external command controller. As an output, provides a means of
acknowledging that the chip has entered debug mode. Asserted as an input,
DE causes the DSP56300 core to finish executing the current instruction, save
the instruction pipeline information, enter debug mode, and wait for commands
from the debug serial input line. This signal is asserted as an output for three
clock cycles when the chip enters debug mode as a result of a debug request
or a breakpoint condition. The DE has an internal pull-up resistor.
DE is not a standard part of the JTAG TAP controller. The signal connects
directly to the OnCE module to initiate debug mode directly or to provide a
direct external indication that the chip has entered debug mode. All other
interaction with the OnCE module must occur through the JTAG port.
DSP56311 User’s Manual, Rev. 2
Freescale Semiconductor
2-19
相关PDF资料
DSPAUDIOEVMMB1E BOARD MOTHER DSP563XX
DSPIC30F2010 DEVELOPMENT KIT KIT DEV EMBEDDED C
DSTRM-KT-0181A DSTREAM DEBUG AND TRACE UNIT
DSUT1CSU SURGE SUPPR NETWORK W/GROUND
DTEL2 SURGE SUPPRESSOR PHONE RJ11/RJ45
DV003001 PROGRAMMER PICSTART PLUS 16C/17C
DV164035 MPLAB ICD3 IN-CIRC DEBUGGER
DV164039 KIT DEV PIC24FJ256DA210
相关代理商/技术参数
DSP56311EVMIG_D 制造商:未知厂家 制造商全称:未知厂家 功能描述:DSP56311EVMIG DSP56311EVM Sample Code
DSP56311EVMUM 制造商:未知厂家 制造商全称:未知厂家 功能描述:DSP56311 Evaluation Module Hardware Reference Manual
DSP56311FACT 制造商:未知厂家 制造商全称:未知厂家 功能描述:DSP56311 Higher performance programmable DSP for demanding voice and data applications
DSP56311UM 制造商:未知厂家 制造商全称:未知厂家 功能描述:DSP56311 24-Bit Digital Signal Processor Users Manual
DSP56311UMAD 制造商:未知厂家 制造商全称:未知厂家 功能描述:DSP56311 Users Manual Addendum
DSP56311VF150 功能描述:数字信号处理器和控制器 - DSP, DSC 150Mhz/300MMACS 150Mhz EFCOP RoHS:否 制造商:Microchip Technology 核心:dsPIC 数据总线宽度:16 bit 程序存储器大小:16 KB 数据 RAM 大小:2 KB 最大时钟频率:40 MHz 可编程输入/输出端数量:35 定时器数量:3 设备每秒兆指令数:50 MIPs 工作电源电压:3.3 V 最大工作温度:+ 85 C 封装 / 箱体:TQFP-44 安装风格:SMD/SMT
DSP56311VF150B1 功能描述:数字信号处理器和控制器 - DSP, DSC 24 BIT DSP RoHS:否 制造商:Microchip Technology 核心:dsPIC 数据总线宽度:16 bit 程序存储器大小:16 KB 数据 RAM 大小:2 KB 最大时钟频率:40 MHz 可编程输入/输出端数量:35 定时器数量:3 设备每秒兆指令数:50 MIPs 工作电源电压:3.3 V 最大工作温度:+ 85 C 封装 / 箱体:TQFP-44 安装风格:SMD/SMT
DSP56311VF150R2 功能描述:数字信号处理器和控制器 - DSP, DSC 24 BIT DSP RoHS:否 制造商:Microchip Technology 核心:dsPIC 数据总线宽度:16 bit 程序存储器大小:16 KB 数据 RAM 大小:2 KB 最大时钟频率:40 MHz 可编程输入/输出端数量:35 定时器数量:3 设备每秒兆指令数:50 MIPs 工作电源电压:3.3 V 最大工作温度:+ 85 C 封装 / 箱体:TQFP-44 安装风格:SMD/SMT